How to Remove and Also Replace a Bath Tub
How to Remove and Also Replace a Bath Tub
Blog Article
This article down below involving A Step-by-Step Guide to Installing a Bathtub is exceptionally interesting. Have a go and draw your own results.
Setting up a tub isn't specifically brain surgery, yet it does call for solid plumbing, carpentry, and in some cases, tiling abilities. Replacing an old tub with a new one is likewise a moderately challenging project. If the old tub is readily accessible, the project can relocate easily; if you need to open a wall to get rid of the old bathtub as well as position the brand-new bath tub, the job is much harder. In either situation, the project is within a home handyman's abilities, although you will certainly require a helper to vacate the old bathtub as well as set in the new one. Make sure you have certified on your own for the task and are comfortable trying it. As opposed to employing a specialist to take over a halfway-completed project, it is far better to take into consideration employing one before you start. Possibilities are you may need a specialist plumber to make tube connections.
This post will aid you install a brand-new bathtub in your shower room if you have currently bought a new bathtub and do not need to change the plan of your previous water supply pipelines.
Your tools as well as material list should consist of the following:
Planning for the Installment
First of all, the sustaining frame provided with the bathroom should be fitted (if needed) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to see to it that if the faucet includes a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the taps system to stop pressure on the tub.
Fit the adaptable tap connectors to the bottom of the two taps making use of 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you utilize every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its final placement.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installation, then the first thing you must do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any water staying in the system. The procedure of getting rid of the existing taps can be quite troublesome because of the restricted accessibility that is often the case.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a towel all set for the remaining water that will certainly originate from the pipelines. Once the supply pipes have actually been gotten rid of, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from transforming throughout this process. When the taps have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Before moving on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Setting up the Bath tub
Utilizing the two wood boards under its feet, put the bath tub in the needed position. The wood boards are useful in equally spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four little points.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by checking the level and readjusting the feet on the bathtub till the spirit level reviews level.
To set up taps, fit all-time low of the outermost versatile faucet port to the ideal supply pipe by making a compression sign up with; then do the exact same for the various other tap.
Activate the supply of water and also check all joints as well as brand-new pipework for leaks and also tighten them if required. Load the bathtub and additionally check the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, deal with the bath paneling as explained in the manufacturer's instruction manual. Tiling and also sealing around the bath tub must wait till the tub has actually been used at the very least once as this will certainly settle it into its last position.
Suitable New Taps
If the tails of the new faucets are plastic, then you will need a plastic connector to avoid damages to the string. One end of the port fits on the plastic tail of the faucet and the other end supplies a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the tap in the placing hole in the bath/basin making sure that the washers are in area between the faucet and the sink. Protect the faucet in place with the maker provided backnut. When the faucet is securely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet adapters. The former kind needs to be connected to the faucet ends first, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the location where the bathroom meets the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to split an inflexible seal, causing the water to penetrate the wall in between the bathroom and also the tiling, leading to problems with wetness and also possible leaks to the ceiling below.
You can select from a selection of coloured sealants to blend in your fixtures as well as fittings. They are offered in tubes as well as cartridges, as well as can securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with twists of soaked newspaper or soft rope. Keep in mind to always fill up the bathtub with water before sealing, to allow for the movement experienced when the tub remains in usage. The sealant can break relatively early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally conveniently readily available on the marketplace. It is advisable to fit the tiles making use of waterproof or water-proof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were shown that article on How to Install a Bathtub from an acquaintance on our other domain. Do you know anybody else who is excited by How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Why not share it. I truly appreciate reading our article about Installing A Bathtub.
View Website
Report this page